Mark Levinson 433 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Audio zesilovače Mark Levinson 433. Mark Levinson 433 Owner`s manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk

Shrnutí obsahu

Strany 1 - Owner’s Manual

No 433Power AmplifierOwner’s Manual

Strany 2 - Important Safety Instructions

10Mark Levinsonpower outage occurs. Power is not disconnected when the Nº433 is in standby or sleep mode.When power returns, the Nº433 will require a

Strany 3

11Nº433 Power AmplifierSpecial Design FeaturesThank you for purchasing the Nº433 Power Amplifier. While this amplifier is straightforward in everyday

Strany 4

12Mark LevinsonExtensive ProtectionThe Nº433 is designed to shut itself down if it senses any of a number of fault conditions that could cause damage

Strany 5 - Table of Contents

13Nº433 Power AmplifierFront PanelThe numbers in the front-panel illustration shown below corre-spond with the numbered items that appear below.1. Ind

Strany 6 - Unpacking

14Mark Levinson2. Power ButtonPowers the Nº433 on and off when the power cord is connected to the ~ac mains connector and an electrical outlet. When t

Strany 7 - Installation Considerations

15Nº433 Power AmplifierRear PanelThe numbers in the rear-panel illustration shown below correspond with the numbered items that appear in the text bel

Strany 8

16Mark LevinsonCaution!NEVER connect power-amplifier outputs to any component other than a loudspeaker.NEVER short circuit power-amplifier outputsNEVE

Strany 9 - Power Requirements

17Nº433 Power Amplifier4. Balanced InputProvides left, center and right-channel audio input. One XLR connector per channel is available to accept bala

Strany 10 - Operating States

18Mark Levinson7. trigger in and out connectorsProvide DC trigger control. One 1/8-inch mini-jack labeled trigger in is available to receive 12 or 5V

Strany 11 - Special Design Features

19Nº433 Power Amplifier9. ~ac mains connectorProvides power to the Nº433 through the supplied power cord when the supplied power cord is connected to

Strany 12 - Extensive Protection

2WARNINGTO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.The lightning flash with arrowhead symbol, with

Strany 13 - Front Panel

20Mark LevinsonLinkingLinking is available for all Mark Levinson components that offer Link or communication ports, including master, slave in, slave

Strany 14 - 3. Standby Button

21Nº433 Power Amplifierother linked components, possibly voiding the manufacturer’s warranty and/or standard repair policies.Constructing LinkCommunic

Strany 15 - Rear Panel

22Mark LevinsonNoteContact an authorized Mark Levinson dealer or Customer Service at www.marklevinson.com for additional assistance making Link connec

Strany 16 - Caution!

23Nº433 Power AmplifierTo create a slave chain that includes the Nº433:1. Make sure the Nº433 and all associated components are powered off.2. Connect

Strany 17 - 6. Communication Ports

24Mark LevinsonRefer to the table on the previous page and to the illustration below for additional assistance. Refer to pages 20-21 for specific cabl

Strany 18 - Important!

25Nº433 Power AmplifierLink ControlsLinking Mark Levinson components allows them to share certain controls. The table below provides a general descrip

Strany 19 - Warning!

26Mark LevinsonTroubleshootingIncorrect operation is sometimes mistaken for malfunction. If problems occur, refer to this section for troubleshooting

Strany 20 - Connections

27Nº433 Power Amplifier4. No audio and the front-panel indicator LED is blinking rapidly, remaining lit most of the time.•A power-related fault is pre

Strany 21 - Communication Cables

28Mark Levinson8. The amplifier keeps powering off.•A fault condition may be present at the input (e.g., a DC signal from the preamplifier) or the out

Strany 22 - Creating a Slave Chain

29Nº433 Power AmplifierCare & MaintenanceThe Nº433 requires routine care and maintenance to ensure optimal performance. The bulleted items in this

Strany 23 - output

39. NEVER attempt to repair this product. If a problem occurs, contact your Mark Levinson retailer.10. NEVER expose this product to extremely high or

Strany 24

30Mark LevinsonSpecificationsThe correlation between published specifications and performance is unreliable. Measurements of your amplifier yield exce

Strany 25 - Link Controls

31Nº433 Power AmplifierDeclaration of ConformityApplication of Council Directive(s):2004/108/EC and 73/23/EEC, as amended.Standard(s) to which Conform

Strany 26 - Troubleshooting

32Mark LevinsonDimensions17.75"45.09 cm7.65"19.4 cm6.97"17.7 cm3.31"8.4 cm5.375"13.7 cm6.75"17.15 cm18.5"47 cm19.83

Strany 27

33Nº433 Power AmplifierRack-MountingIf you need or prefer to rack mount your amplifiers contact your Mark Levinson dealer for information about the op

Strany 28 - 9. If all else fails

3 Oak Park, Bedford, MA, 01730-1413 USA | Telephone: 781-280-0300 | Fax: 781-280-0490 | www.marklevinson.comCustomer Service: Telephone: 781-

Strany 29 - Care & Maintenance

43 Oak ParkBedford, MA 01730-1413 USATelephone: 781-280-0300Fax: 781-280-0490www.marklevinson.comCustomer ServiceTelephone: 781-280-0300Sales Fax: 7

Strany 30 - Specifications

5Nº433 Power AmplifierTable of ContentsUnpacking ...6Product Regist

Strany 31 - Declaration of Conformity

6Mark LevinsonUnpackingWarning!DO NOT attempt to lift or move the Nº433 without adequate assistance. Failure to follow the procedures included in this

Strany 32 - Dimensions

7Nº433 Power AmplifierInstallation ConsiderationsThe Nº433 requires special care during installation to ensure optimal performance. Pay particular att

Strany 33 - Rack-Mounting

8Mark Levinson• DO NOT place the Nº433 on a thick rug or carpet or cover the Nº433 with a cloth, as this might prevent proper cooling. If the Nº433 is

Strany 34

9Nº433 Power AmplifierPower RequirementsWhen shipped, the Nº433 is configured for 100V, 120V, 220V, 230V or 240V AC power operation at 50 or 60Hz base

Komentáře k této Příručce

Žádné komentáře